Glue down vinyl flooring, also called dry back LVT, is thin luxury vinyl, typically around 2mm to 2.5mm thick, that is bonded to a smoothed subfloor with adhesive instead of clicking together. Because every plank is fixed down, the floor cannot move as a whole: it stays flat and stable under heavy rolling loads, strong sunlight and big temperature changes, and large, open areas can be laid without expansion breaks.
It is the professional standard for shops, offices and other commercial spaces, and the best choice at home for large open-plan rooms, conservatories, kitchens with heavy use and pattern floors such as herringbone, where thin glue-down planks allow borders and intricate layouts. A damaged plank can be cut out and replaced. Compare it with vinyl click flooring and rigid SPC flooring, which float over an underlay and are quicker to fit.
See heavy-use ranges in commercial vinyl, sunny rooms in conservatory LVT, and pattern in herringbone LVT. You will need a vinyl floor adhesive, and our luxury vinyl guide explains wear layers and cores.
Not sure which floor is right? Order free samples and see them in your own light, or call our team on 020 3287 6206 for honest, no-pressure advice.
Colour
Price per m²
- £10 – £19.99 (12)
Floor Style
Vinyl Type
- Dryback (glue down) (12)
Effect
- Oak Effect (7)
- Wood Effect (8)
Thickness
- 2.5 12
Wear Layer
- 0.5 (12)
Width
- 221mm+ (12)
Length
- 801–1999mm (planks) (12)
Room Suitability
- Bathroom (12)
- Bedroom (12)
- Conservatory (12)
- Dining Room (12)
- Hallway (12)
- Kitchen (12)
- Living Room (12)
- Study / Office (12)
- Utility Room (12)
Showing all 12 results
Verno Amber Wheat Oak Vinyl Flooring 2.5 x 235mm
Verno Arctic White Vinyl Flooring 2.5 x 235mm
Verno Highland Natural Oak Vinyl Flooring 2.5 x 235mm
Verno Manor Grey Oak Vinyl Flooring 2.5 x 235mm
Verno Midnight Oak Vinyl Flooring 2.5 x 235mm
Verno Morning Frost Oak Vinyl Flooring 2.5 x 235mm
Verno Nebula White Vinyl Flooring 2.5 x 235mm
Verno Sandy Oak Vinyl Flooring 2.5 x 235mm
Verno Smoked Charcoal Vinyl Flooring 2.5 x 235mm
Verno Smoked Grey Vinyl Flooring 2.5 x 235mm
Verno Snowy Hickory Vinyl Flooring 2.5 x 235mm
Verno Tawny Oak Vinyl Flooring 2.5 x 235mm
Filters By
Verno Amber Wheat Oak Vinyl Flooring 2.5 x 235mm
Verno Arctic White Vinyl Flooring 2.5 x 235mm
Verno Highland Natural Oak Vinyl Flooring 2.5 x 235mm
Verno Manor Grey Oak Vinyl Flooring 2.5 x 235mm
Verno Midnight Oak Vinyl Flooring 2.5 x 235mm
Verno Morning Frost Oak Vinyl Flooring 2.5 x 235mm
Verno Nebula White Vinyl Flooring 2.5 x 235mm
Verno Sandy Oak Vinyl Flooring 2.5 x 235mm
Verno Smoked Charcoal Vinyl Flooring 2.5 x 235mm
Verno Smoked Grey Vinyl Flooring 2.5 x 235mm
Verno Snowy Hickory Vinyl Flooring 2.5 x 235mm
Verno Tawny Oak Vinyl Flooring 2.5 x 235mm
Why choose glue-down vinyl?
- Stable: bonded planks cannot shift, so the floor stays flat under office chairs, trolleys and heavy furniture.
- Large areas: no expansion breaks needed across big open-plan spaces, as floating floors often are.
- Sun and heat: bonded to the subfloor, it copes with conservatories and big south-facing windows better than floating floors.
- Repairable: one damaged plank can be lifted and replaced.
- Design freedom: herringbone, borders, strips and mixed sizes are easier with thin planks.
- Quiet and low: bonded vinyl sounds solid, and adds only a few millimetres to the floor height.
The downsides to know
Glue-down vinyl needs a perfectly smooth, flat, dry subfloor, because a thin floor shows every bump, crack and grain of what is underneath. That usually means priming and applying a smoothing (levelling) compound before laying. Fitting is slower and messier than click flooring, and it is usually done by a professional fitter. Lifting it later is also more work.
Subfloor preparation
- Check concrete is dry with a moisture test; damp slabs need a moisture barrier system.
- Repair cracks and remove old adhesive, paint and contamination.
- Prime the subfloor, then apply a smoothing compound to give a flat, smooth surface.
- Over timber floors, overlay with plywood fixed at close centres, then smooth if needed.
- Let everything dry fully before laying.
Choosing the adhesive
Use an adhesive recommended for the vinyl and the conditions: standard adhesives for most rooms, and high-temperature or two-part adhesives for conservatories, sunny rooms and areas with underfloor heating, as the maker advises. Follow the stated trowel notch, open time and coverage.
Choosing glue-down vinyl
Wear layer
0.3mm for light domestic use; 0.55mm for busy homes and light commercial; 0.7mm or more for heavy commercial areas.
Thickness
Most dry back LVT, sometimes called 2mm vinyl flooring, is around 2mm to 2.5mm; thicker products may have a thicker wear layer.
Look
Every wood and stone look is available, plus pattern pieces for herringbone and chevron.
Glue-down or click vinyl?
Glue-down: large, sunny or heavy-use spaces, commercial premises and intricate patterns; needs a prepared subfloor and a fitter. Click (SPC): most homes, quicker DIY fitting and floats over many existing floors; large areas may need expansion breaks.
Laying glue-down vinyl
Acclimatise the planks, set out the layout from a centre line, spread adhesive with the correct trowel, lay the planks within the open time and roll the floor with a heavy roller to bond it fully. Keep traffic off until the adhesive has set, as the maker states. Our installation guides cover glue-down LVT, and our measuring guide helps with quantities.
Comparing samples at home
Order free samples of two or three options and put them on the floor of the room where they will be laid. Look at them in daylight and in the evening under your own lamps, next to the walls, skirting, units and furniture they will sit with. Colours and textures look different in every room and on every screen, so a few minutes with real samples is the best way to avoid a costly mistake. Stand back as well as looking close up: a floor is mostly seen from standing height and from the doorway.
Looking after glue-down vinyl
Sweep or vacuum regularly and damp mop with a pH-neutral cleaner. Use entrance matting, chair mats under castor chairs and felt pads under furniture.
Common mistakes
- Laying on an unsmoothed subfloor, so every bump shows through.
- The wrong adhesive for a sunny conservatory or heated floor.
- Skipping the roller, so planks do not bond fully.
FAQs on Glue Down Vinyl Flooring
Thin luxury vinyl, also called dry back LVT, bonded to a smoothed subfloor with adhesive rather than clicked together.
For large, sunny or heavy-use areas, yes. For most homes, click vinyl is quicker and easier to fit.
Usually around 2mm to 2.5mm, which is why it is sometimes called 2mm vinyl flooring.
It is possible, but the subfloor preparation is critical. Most people use a professional fitter.
No. It is bonded directly to a primed, smoothed subfloor.
Yes. Bonded planks cope with sun and heat better than floating floors; use an adhesive suitable for high temperatures.
Newsletter Subscribe
It only takes a second to be the first to find out about our latest news and promotions...