Tongue and groove engineered wood flooring uses the traditional joint for wood floors: each board has a tongue along one edge and end, which slots into a groove in the next board. Tongue and groove engineered oak flooring is usually glued down to the subfloor, or floated with glue in the joints, which gives a very solid, quiet floor, and it is the standard for herringbone and chevron parquet and for many premium wide-board floors.
Because the joints do not lock by themselves, fitting takes more skill than click flooring, and most people use an experienced fitter. In return, glued tongue and groove floors feel like solid wood underfoot, suit large open spaces and are often recommended over underfloor heating. Compare click engineered wood, which floats and locks without glue, or see glue-down engineered wood.
You will need a wood floor adhesive, or an engineered wood flooring underlay for floating installation. Patterns are in engineered parquet, and every board in engineered oak. Our engineered wood guide explains construction.
Not sure which floor is right? Order free samples and see them in your own light, or call our team on 020 3287 6206 for honest, no-pressure advice.
Colour
Finish
Price per m²
- £70 and over (1)
Floor Style
Thickness
- 19 1
Species
- Oak (1)
Grade
- Rustic (1)
Wear Layer
- 5 (1)
Width
- 180–220mm (1)
Length
Joining Method
- Tongue & Groove (1)
Room Suitability
- Bedroom (1)
- Conservatory (1)
- Dining Room (1)
- Hallway (1)
- Kitchen (1)
- Living Room (1)
- Study / Office (1)
Suprima Smoked White Brushed & Oiled Rustic Engineered Oak Flooring 19/5 x 220mm
Filters By
Suprima Smoked White Brushed & Oiled Rustic Engineered Oak Flooring 19/5 x 220mm
How tongue and groove works
Each board has a tongue machined along one long side and one end, and a matching groove along the opposite side and end. Boards are slid together so the tongue fits snugly into the groove. Unlike click joints, they do not lock mechanically, so they are held by adhesive (to the subfloor or in the joints) or by secret nails through the tongue into a timber subfloor.
Ways to fit tongue and groove engineered wood
Glued to the subfloor
Boards are bonded to a dry, flat, primed subfloor with an elastic wood floor adhesive. The most solid, quiet result and the best heat transfer over underfloor heating; the usual method for parquet and wide boards.
Floated with glue in the joints
Boards are laid over an underlay and a bead of wood glue is run along the groove, bonding the boards into one floating sheet. Quicker than full glue-down, but the floor cannot easily be lifted.
Secret-nailed
To a timber subfloor, through the tongue at an angle, where the maker allows.
Tongue and groove or click?
Tongue and groove: traditional, very solid when glued, ideal for parquet, wide boards, large areas and underfloor heating; more skill and time. Click: quick, DIY-friendly, floats without glue and can be lifted later; can sound a little hollower.
How to choose
Check the top layer depth (how often it can be sanded), the board thickness, the grade and finish, and whether it is approved for underfloor heating. Tongue and groove boards are made in every look, from rustic to prime grade, natural to smoked oak, planks to herringbone.
Tongue and groove engineered wood room by room
Open-plan spaces: glued down, one continuous solid floor. Rooms with underfloor heating: glued, with an adhesive approved for heated floors. Herringbone hallways: the traditional method. Kitchens: a durable finish, glued down, spills wiped promptly. Bathrooms: never real wood.
Fitting tips
- Acclimatise the boards in the room.
- Check the subfloor’s moisture and flatness, and prime it if the adhesive requires.
- Start along a straight line, tongue facing out, and leave an expansion gap at the walls.
- Tap boards together gently with a tapping block; never hit the tongue directly.
- Clean adhesive off the face of the boards immediately.
- Keep traffic off until the adhesive has cured.
Our installation guides explain each method.
Tongue and groove for parquet
Most herringbone and chevron parquet is made with tongue and groove joints and glued down, which holds the small blocks tight and flat and lets the pattern be built accurately from a centre line. If you want a parquet floor with the most solid, traditional result, glued tongue and groove is the standard.
Comparing samples at home
Order free samples of two or three options and put them on the floor of the room where they will be laid. Look at them in daylight and in the evening under your own lamps, next to the walls, skirting, units and furniture they will sit with. Colours and textures look different in every room and on every screen, so a few minutes with real samples is the best way to avoid a costly mistake. Stand back as well as looking close up: a floor is mostly seen from standing height and from the doorway.
Looking after it
Vacuum regularly, use door mats and felt pads, and clean with a pH-neutral wood floor cleaner. A glued tongue and groove floor can be sanded and refinished as its top layer allows.
Common mistakes
- Floating tongue and groove boards without glue in the joints, so they separate.
- Gluing to a damp or uneven subfloor.
- Damaging the tongue by hammering it directly.
FAQs on Tongue & Groove Engineered Wood Flooring
Engineered oak with a traditional tongue and groove joint, usually glued down or floated with glue in the joints.
Yes, with glue run along the joints so the boards bond into one floating floor.
Tongue and groove is more solid when glued; click is quicker and DIY-friendly.
Yes, glued down with an adhesive approved for heated floors.
It takes more skill than click flooring; most people use an experienced fitter.
Yes, secret-nailed through the tongue to a timber subfloor, where the maker allows.
Newsletter Subscribe
It only takes a second to be the first to find out about our latest news and promotions...