Lacquered Engineered Wood Flooring

Lacquered engineered wood flooring is real oak protected by a clear, hard-wearing lacquer that forms a sealed layer on top of the wood. That layer keeps spills, dirt and stains on the surface, so a lacquered floor is easy to clean and needs very little maintenance: no regular oiling, just sweeping and a damp mop. It is the practical choice for busy family homes, hallways and kitchens, and for anyone who wants real wood without the upkeep.

Modern lacquers are nothing like the shiny, orange floors of the past. Matt and ultra-matt lacquered wood flooring looks close to raw or oiled wood, while satin gives a soft sheen. Lacquered engineered oak flooring comes in natural, light, smoked and grey tones, and in brushed textures such as brushed and lacquered oak. Compare it with oiled engineered wood, which looks more natural and is easier to spot-repair.

See solid boards in lacquered solid wood, or every lacquered oak flooring style in engineered oak. For kitchens, see engineered wood for kitchens. Lacquered floors are cleaned with wood floor cleaner and refreshed with wood floor polish. Our engineered wood guide explains finishes.

Not sure which floor is right? Order free samples and see them in your own light, or call our team on 020 3287 6206 for honest, no-pressure advice.

Showing all 6 results

Lacquer or oil?

Lacquer forms a hard, clear layer on top of the wood. It resists spills and stains best, needs little maintenance and is easy to clean. Its weakness: a deep scratch cuts through the layer and is harder to repair invisibly, and worn areas are renewed by sanding and re-coating rather than spot-repaired. Oil soaks into the wood. It looks and feels more natural, and scratches and worn patches can be repaired locally, but it needs regular maintenance oiling, especially in busy areas.

Choosing the sheen

  • Ultra-matt and matt: close to the look of raw or oiled wood; hides scratches and footprints best. The most popular choice today.
  • Satin: a gentle sheen, slightly more classic.
  • Gloss: a traditional shiny look that shows every scratch and footprint; rarely used on new floors.

Where lacquered engineered wood works best

  • Kitchens: spills stay on the surface, ready to be wiped up.
  • Hallways: easy to clean after wet, muddy days.
  • Family homes and rental properties: low maintenance, with no oiling schedule to remember.
  • Homes with pets: stains and accidents wipe off the sealed surface; a matt finish hides claw marks better.

Looking after a lacquered floor

  1. Sweep or vacuum regularly: grit is what scratches lacquer.
  2. Damp mop with a well-wrung mop and a pH-neutral wood floor cleaner.
  3. Never use a steam mop, bleach or abrasive cleaners.
  4. Use felt pads under furniture and mats at outside doors.
  5. Refresh dull walkways with a polish made for lacquered floors, which fills fine scratches and restores the sheen.

Renewing the lacquer

After many years, when the lacquer wears through in walkways, the floor can be lightly sanded (screened) and given a fresh coat of lacquer, without sanding into the wood. If the oak itself is scratched or worn, a full sand and re-lacquer renews the floor, as far as its top layer allows.

UV lacquer

Many pre-finished boards are coated with UV-cured lacquer at the factory, which is very hard and consistent. Maintain it with the products the maker recommends.

Fitting lacquered engineered wood

Let the packs acclimatise, check concrete with a moisture meter, and float the boards over an engineered wood flooring underlay or glue them with a wood floor adhesive. Protect the finished surface during fitting and any decorating that follows; tape and dust sheets can mark fresh lacquer. Our installation guides explain each method.

Comparing samples at home

Order free samples of two or three options and put them on the floor of the room where they will be laid. Look at them in daylight and in the evening under your own lamps, next to the walls, skirting, units and furniture they will sit with. Colours and textures look different in every room and on every screen, so a few minutes with real samples is the best way to avoid a costly mistake. Stand back as well as looking close up: a floor is mostly seen from standing height and from the doorway.

Common mistakes

  • Applying oil to a lacquered floor, where it cannot soak in.
  • Steam mops, which can damage the lacquer and the joints.
  • Choosing gloss for a busy family home.
  • Using furniture polish or wax-based products, which leave a slippery film on the lacquer.

Lacquered engineered wood room by room

Kitchens: a matt lacquer keeps spills on the surface; wipe them promptly and seal the expansion gap at the plinths. Hallways: easy to clean after muddy days, with a good door mat. Living rooms and bedrooms: a calm, low-maintenance real wood floor. Rentals: no oiling schedule for tenants to forget. Homes with pets: a brushed, matt lacquer hides claw marks best. Never use any wood floor in a bathroom.

FAQs on Lacquered Engineered Wood Flooring

Yes. The sealed lacquer layer resists spills, stains and everyday wear, and it needs little maintenance.

Not necessarily. Matt and ultra-matt lacquers look close to raw or oiled wood.

Fine scratches can be hidden with a polish for lacquered floors; deep ones need sanding and re-lacquering.

Lacquered is usually more practical for kitchens: spills stay on the surface and there is no oiling to keep up.

Only after many years, when the lacquer wears through in walkways; a light sand and fresh coat renews it.

No. Steam can damage the lacquer and the joints. Use a well-wrung mop and a wood floor cleaner.

Newsletter Subscribe

It only takes a second to be the first to find out
about our latest news and promotions...